 |
Server Help
Community forums for Subgame, ASSS, and bots
|
| Author |
Message |
Donkano
Server Help Squatter
Gender:
Joined: Jul 02 2003
Posts: 763
Offline
|
 Posted: Mon Aug 16, 2004 8:21 pm Post subject: Routers... |
 |
 |
|
|
Okay, I was reading wEaViL's guide to router set-up
| wEaViL wrote: | This tut will work for Linksys and Networkeverywhere routers, for a generic version go to Generic Router HowTo
Not 100% sure but I know how to get the Linksys BEFSR41 Router to run a zone from your pc.
NOTE: you may be able to skip steps 1 and 2, I recremend that you do unless it still does not work.
1. Upgrade your firmware to the current one. Go to http://www.linksys.com/ search support for firmware upgrade
and follow there instructions.. NOTE: Read all instructions 1st and make note of current router settings before doing this as it will set the router back to default.
To check your router settings and make a list type 192.168.1.1 into your webbrowser. If you have not set a username and pass then leave the username empty and type admin in lowercase in the password box then click ok.
2. After you have upgraded your firmware go back into the router and reinput all the settings you copied in step 1.
3. Now your ready for the fun stuff assuming all your computers can use the internet again. Go into your router again via the 192.168.1.1 and input the username and pass or just admin as pass. Once inside the routers setup click on the DHCP tab. Once in there click on the Enable DHCP, if needed you may have to insert the last 3 numbers in the starting ip address, for example 192.168.1.100 as where your ips will be 100 102 103 and so on. Number of DHCP users set this to 50, as long as that number is higher then the number of computers using the router you'll be ok.
4. After you have applied the previous step you want to go back into the DHCP tab and scroll down. Click on the DHCP clients table. This will pop up a box with all the computers currently connected to the router. Look for your pc that the server is one, the name of the computer should be listed along with its ip address the router gives it. EX. 192.168.1.105 Make note of this number as your will need it.
5. Now click on the advanced tab. This will put you on the Filters page. Scroll down to the bottom and look for a item called Block WAN requeast Make sure it is disabled. If it is not then the router will not forward anything to the comp running the server.
6. Now click on the Fowarding tab. This section will be a lil bit different depending on the firmware you are running. Since I am running the uptodate one if your running a older one you might not see what I say. Mine has a section named Customized Application section, in that on the 1st box I typed subgame2. If yours does not have it then dont worry. Now you need to input the port and +1 port of your server.. Ex if your server port is 5000 you want to put in 5000 TO 5001. The port number you need will be found in the MISC section of your server.ini file. Now select the protocol UDP and under the ip address insert the one you wrote down from step 4. [EX 192.168.1.105] Now click enable. Scroll down and click apply.
7. Now you need to know the real IP address of your comp. Click this http://www.whatismyip.com/ and write down the IP it tells you. Thx for the link GGTM The IP should look something like 65.66.45.156 or whatever..
8. Open the server.ini file again and scroll down to the MISC section and look for Server IP Input the IP number that website gave you. Now save your ini file.
9. Open the Zone.dat file (if using Catid billing) To open the file right click it and select Open With.... on the box that opens click on the wordpad down at the bottom of the list. Once inside it type in
MY Server,64.34.187.36,5000,,0 <--- Your IP the website gave you
#My Server
MY Server,192.168.1.105,5000,,0 <--- Your IP the router gave you
#My Server
(thx again GGTM)
Now save that file and exit...
10. Now run the subbill.exe file and then the subgame2.exe file and they should connect assumeing you set them up right prior to this. Now your zone should be able to be used by users outside of your lan. The only way you will know is if someone decides to see what your zone is like or if you do like me and go to a friends house and redownload the list of zones then try to enter yours. If it works then WALA im good  |
I got the BEFSR41 router and I am now stuck on the part where I connect to http://192.168.1.1/ and I don't know my username and password to access the router! How do I find this out? |
|
| Back to top |
|
 |
Donkano
Server Help Squatter
Gender:
Joined: Jul 02 2003
Posts: 763
Offline
|
| Posted: Mon Aug 16, 2004 9:16 pm Post subject: |
|
|
|
|
| nm, I got it. |
|
| Back to top |
|
|
wEaViL
Don't make me turn this forum around!
Age:45
Gender:
Joined: Feb 17 2003
Posts: 829
Location: nc usa
Offline
|
| Posted: Tue Aug 17, 2004 4:29 am Post subject: |
|
|
|
|
| Donkano wrote: | | wEaViL wrote: | | input the username and pass or just admin as pass |
|
The answer was in front of you.  |
|
| Back to top |
|
|
|
|
You can post new topics in this forum
You can reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum
|
Software by php BB © php BB Group
Server Load: 32 page(s) served in previous 5 minutes. |
FAQ
Search
Memberlist
Usergroups
Statistics
Register
Profile
Login to check your private messages
Login
need help getting my zone to work 
